English
Cart €0,00

Welcome, guest, you can Login or Create an account

View all results (0)
No products found...
Home » Arduino Nano Motor Drive Shield 2 Ampere
Arduino Nano Motor Drive Shield 2 Ampere
Arduino Nano Motor Drive Shield 2 Ampere

Not yet rated Add your review

€14,95

Incl. tax
Article number:
AR0164
SKU number:
AK21
Availability:
Out of stock
Delivery time:
3-4 weken

Arduino Nano Motor Drive Shield 2 Ampere

+ -
Add to cart
Add to wishlist Add to comparison

The NANO Motor Shield is based on the L298P, which is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors. It lets you drive two DC motors with your For Arduino NANO board, controlling the speed and direction or each one independently. You can also measure the motor current absorption or each motor, among other features.

• You can find in the Getting Started section all the information you need to configure your board, use the For Arduino Software (IDE), and start tinker with coding and electronics.
 

Technical specs

 

Operating Voltage

5V to 12V

Motor controller

L298P, Drives 2 DC motors or 1 stepper motor

Max current

2A per channel or 4A max (with external power supply)

Current sensing

1.65V / A

Free running stop and brake function

 
 
 
Power
 
The NANO Motor Shield must be powered only by an external power supply. Because the L298 IC mounted on the shield has two separate power connections, one for the logic and one for the motor supply driver. The required motor current often exceeds the maximum USB current rating.
External (non-USB) power can come either from an AC-to-DC adapter (wall-wart) or battery. The adapter can be connected by plugging a 2.1mm center-positive plug into the Arduino's board power jack on which the motor shield is mounted or by connecting the wires that lead the power supply to the Vin and GND screw terminals, taking care to respect the polarities.
To avoid possible damage to the Arduino board on which the shield is mounted, we use an external power supply that provides a voltage between 7 and 12V. If your motor require more than 9V we recommend that you separate the power lines of the shield and the For Arduino board on which the shield is mounted. This is possible by cutting the "Vin Connect" jumper placed on the back side of the shield. The absolute limit for the Vin at the screw terminals is 18V.
The shield can supply 2 amperes per channel, for a total or 4 amperes maximum.
 
Input and Output
This shield has two separate channels, called A and B, that each use 4 of the For Arduino pins to drive or sense the engine. In total there are 8 pins in use on this shield. You can use each channel separately to drive two DC motors or combine them to drive one bipolar stepper motor. The shield's pins, divided by channel are shown in the table below:

Function

pins per Ch. a

pins per Ch. B

Direction

D12

D13

PWM

D3

D11

Brake

D9

D8

Current Sensing

A0

A1
 
If you don't need the Brake and the Current Sensing and you also need more pins for your application you can disable this features by cutting the respective jumpers on the back side of the shield.
 
 
Motors Connection
 
Brushed DC motor. You can drive two Brushed DC motors by connecting the two wires of each one in the (+) and (-) screw terminals for each channel A and B. In this way you can control its direction by setting HIGH or LOW the DIR A and DIR B pins, you can control the speed by varying the PWM A and PWM B duty cycle values. The Brake A and Brake B pins, if set HIGH, will effectively brake the DC motors rather than let them slow down by cutting the power. You can measure the current going through the DC motor by reading the SNS0 and SNS1 pins. On each channel will be a voltage proportional to the measured current, which can be read as a normal analog input, through the function analogRead () on the analog input A0 and A1. For your convenience it is calibrated to be 3.3V when the channel is delivering its maximum possible current, that is 2A.
 
Add your review

Categories

Recently viewed Clear

Loading...
Arduino Nano Motor Drive Shield

Arduino Nano Motor Drive Shield

€14,95

Payment method

iDEAL PayPal Visa Maestro Bancontact / Mister Cash SOFORT Banking MasterCard Belfius Bank transfer KBC American Express Giropay EPS ING HomePay Cartes Bancaires Klarna Pay Later (BETA)

Brands

Please accept cookies to help us improve this website Is this OK? Yes No More on cookies »