XY-J04 timer with delay switch

Trigger cycle delay switch circuit double MOS tube control board instead of relay module 12 24 v

0.1 second (min) ~ 999 min (max) continuously tunable

Module features and applications:

• Achieve high frequency and frequent circuit breakage and unlimited number of switches.
  
  
• Interruption process produces no sound, no electric spark and no electromagnetic interference.
  
  
• The service life is longer than that of the commonly used electromagnetic relays.
  
  
• Dual MOS parallel active output, lower internal resistance, larger current and strong power. 15A and 400w at room temperature meet the needs of most devices.
  
  
• Often used for checking motors, light bulb, LED, DC motor, micro pump, electromagnetic valve and so on

Module highlights:

1. Wide voltage (5 ~ 36 v), most equipment can be used.
2. The interface is clear and simple, powerful, easy to understand, almost all your needs.
3. There is a button emergency stop function (STOP), with reverse connection protection, reverse connection without burning.
4. increased sleep mode, preventing use after 5 minutes, automatically turning off the monitor.

Wake-up by a test;

5. You can set different parameters of OP, CL and LOP, which are independent of each other.
6. All set parameters automatically save the power.

Work model:

P1 mode: after the signal is activated, the relay conducts ON time and then disconnects; in OP time, the following operations are performed.

P1.1: signal again trigger invalid

P1.2: the signal triggers the time again

P1.3: the signal is reactivated, the relay is disconnected, and the timer has stopped.

P-2: activate signal, the relay breaks the CL time, the relay conducts ON time, and after the timer is complete, the relay is disconnected.

P3.1: after the trigger signal is activated, the relay opens the time of OP, the relay breaks the CL time, and then the above action circulates, the relay is given the signal again, the relay is disconnected and the timing is stopped ; the cycle times (LOP) can be set;

P3.2: after power on, there is no need to trigger the signal, the relay can lead ON time, the relay breaks CL time, circulate the above actions, and the number of cycles (LOP) can be set.

P-4: if the signal has a trigger signal, the timing is zero, the relay is kept open; when the signal disappear, the relay is broken after the time of time ON; during the time of time, the signal is repeated and the time is zero;

Product parameters:

1: working voltage: DC 5V - 36V;

2: trigger signal source: high level trigger (DC 3.0 v-24 v) signal and system do not share common ground to improve the anti-jamming ability of the system.

3: output power: DC DC 5V - 36V, constant current 15A at room temperature, power 400 w! Under the condition of additional heat dissipation, the maximum current can reach 30A.

4: static current: 15 mA

5: service life: infinite switch; working temperature: -40-85 C; size: 6.0 * 3.4 * 1.2 cm

6: with optocoupler isolation, anti-interference ability, industrial grade circuit boards, set parameters after power failure lasting memory.

Special attention:

The module is active electrified output, and the output (load side) voltage equal to the input voltage (DC 5V - 36V).

The 'DC +' and the load '+' poles themselves are internal short connections, but the DC 'and load' - 'poles cannot be short connected during use, otherwise the load will not be checked to open and turn on, Equal to the tax that is all the time.

Time range

0.1 second (min) ~ 999 min (max) continuously tunable

How the time range:

After setting the parameter values in the mode selection interface, select the time range by briefly pressing the STOP key.

XXX. comma in bit, time range: 1 second ~ 999 sec.

1. X comma in ten places, time range: 0.1 seconds ~ 99.9 seconds.

XXX the comma is clear. The time range is 1 minutes ~ 999 minutes.

For example, if you want to set OP 3.2 seconds, move the comma to ten bits, and the digital tube displays 3.2.

Parameter Description: ON lead time, CL disconnection, LOP cycle number (1 to 999 times, "---" represents infinite cycle).

These parameters are independent of each other, but each pattern shares these parameters, for example, in the P1.1 setting the adjust time ON is 5 seconds, the user wants to switch to the P1.2 mode, then the ON will be 5 seconds when the corresponding parameters are set in the P1.2;

On the main interface (display 000), short on SET button will display ON (CL, LOP) and the corresponding time XXX;

If there is only OP (for example, mode P1.1, P1.2, P1.3) in the cartridge, then the short SET key leaves only OP and the corresponding time.

If there is OP, CL and LOP (for example, mode P3.1, P3.2) in the pattern, the short press of SET key will display ON and corresponding time, CL and corresponding time, LOP and corresponding times;

After setting up the mode, you can easily view the parameters in the current mode by briefly pressing the SET key in the main interface, which is very convenient.

How parameters

1. first, determine the operating mode of the relays.
2. According to the working mode of the relay, when the main interface is on the main interface, it will flicker the current working mode (the standard P1.1 mode), and then enter the main interface, and "long press SET key" in the mode selection interface after 2 seconds, And select the mode to set by briefly pressing UP and DOWN keys (P1.1 ~ P-4).
3. After selecting the mode to up (for example, P3.2) set the corresponding parameters by the SET key, the parameters to be set will flicker (ON conduction time, CL break time, LOP cycle times ("-" for infinite cycle)), set the parameter values through UP, DOWN, Support long press (rapid increase or decrease) and short (Add or reduce 1 units); set a good parameter value, by briefly pressing STOP key to the decimal point, select the time range (the corresponding time 0.1 seconds ~ 999 minutes); Briefly press SET key, Set the following parameter of the current mode, the process is the same.
4. the parameters of the selected mode, after the long press on SET 2 seconds disconnected, the current set pattern will flicker, and then back to the main interface, setting the parameters successfully, very easy!

Main interface: relay not working state display "000" (no comma), relay working state with decimal point, very clear!

Mode selection interface: long press SET key to, after setting up, long press SET key to exit, back to main interface, very easy!

STOP key function extension:

Relay enabled mode:

The relay is transmitted in the 1. OP: OP conduction time.

2. OFF: the relay is forbidden on and is always closed.

In the main interface, press STOP button to switch between ON and OFF. The current state will blink and then return to the main interface. (this function is emergency stop function, a key breaks closed relay).

Sleep pattern:

1. cP sleep mode: five minutes, no operation, digital tube automatic closing display, normal program operation;
2. Od normal mode: digital tube always opens and displays.

On the STOP button for 2 seconds turn the CP and Od status.